Wire the LCD RKP as shown in the wiring section of this manual. Replace the .. The Eurosec CP8 LCD has two log modes. These are: a). gardtec eurosec cpx installation manual · Home · Blog · About · Press · Contact · Home · Blog · About · Press · Contact. Powered by カスタマイズ可能なテンプレート . A range of alarm system user guides and manuals for owners and clients. Accenta 6 · Euro 46 User Manual · Euro Mini User Guide · Eurosec CP7/CP8 LED .
|Published (Last):||4 April 2011|
|PDF File Size:||2.76 Mb|
|ePub File Size:||3.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
Before attempting to reset your system eurisec that the system is Un-set. If the system was Unset only the internal sounders will operate. It is important that your security system is serviced on a regular basis on order that it continues to comply with the legislation. My order number is if you could kindly send me the engineer manual please.
Eurosec CPX User guide – Home Security Systems
See Advanced Code Programming section for details. In this instance using will send a Duress code to your central station when you Set or Unset your system. G-Tag conforms fully with the requirements of this legislation relating to confirmed alarms on entry. Posted 31 December – If the system is Unset when the Tamper occurs the alarm will be internal sounders only. Then choose Can or Cant Unset dependant on your requirements.
The User Code levels available and the functions available for the levels are: Please PM One of us directly if your query is not of a public nature.
Care must be taken with Duress codes, misuse of Duress codes may lead to the loss of police response. Remember me This is not recommended for shared computers. Several parameters will need to be programmed by the installation company before a Control Code may be programmed into the system.
CPX programming guide/manual – Intruder Alarms – Security Warehouse Support Forum
Duress Codes may also be used on this system for activating Personal Alarms P. I assume you have recieved it ok?
If you instwllation not choose to Set or Unset the system within the ten seconds the top line of the display will be blanked out and the code entry will be invalidated. Community Forum Software by IP. The Proximity Reader may be built in to the keypad or be an external reader that is fitted into a doorframe etc. If you do so your system may be adversely affected 1 With the display showing: In the event of a sustained power cut the system battery will continue to supply the system until the battery voltage falls to a set point, at his stage the display will show: In order for this to function additional hardware would be required.
If you wish to accept the name shown press Yes and jump to step 13 Code Type.
About – gardtec eurosec cpx installation manual
Page 5 15 PR At this point it is essential that you contact your installation company. Pressing YES will move forward to the next event.
Read Log 01 JAN Before Vo-Comm can work several mahual will need to be programmed. A Master level code may change the status of the Chime between On and Off.
The alarm may be silenced by entering a valid User Code. Setting or Unsetting the system using the code that is programmed as User 7 will activate a Duress signal. At this point the system will revert to battery back-up The battery will only have a limited time that it can sustane the system for. If you do not acknowledge the call or hear the rising tone the Vo-Comm will repeat the message several times and then go on to dial the remaining telephone numbers until the call is acknowledged.
Normal To set the system with a normal keyswitch, insert the key and turn to the ON position then remove the key. I mean do some kind of connection or make any changes through the keypad? Wait until the exit tone finishes before leaving. G-Tag Proximity Tags may be used for setting and unsetting the system. This determines if using this user code to Set or Unset the system will trigger the Vo-Comm for more details on Vo-Comm please refer to the Vo-Comm section. Follow the instructions from step 3 above.
Because the G-Tag uses Proximity Technology there are no batteries to change in the unit, it is small enough to be carried on the users key ring and one Tag may be used on multiple security mwnual and some door entry systems.